Auto components
Machining, paint and stores separation in NIT and Sector 24 plants.

Faridabad · served from Gurugram & Neemrana
PVC and self-repairing high-speed doors for Faridabad's auto-component, engineering and warehousing units. Built at our Neemrana works and installed by our NCR team from the Gurugram office.
In Faridabad's component plants a single internal opening can see forklifts and trolleys all shift, between machining, paint and stores. A high-speed door opens for the pass and closes behind it, so dust, heat and noise stay where they belong. We have no premises in Faridabad: doors are built at Neemrana and installed and serviced by the NCR team at our Gurugram office.
The range, numbered

Flexible PVC curtain on a spiral or belt drive for internal openings and washdown areas.
View pvc high-speed door
Zipper-edge curtain that re-seats itself after a forklift knock, so a strike does not stop the line.
View self-repairing door
Insulated fast door for chillers and dispatch docks, sealing the aisle against temperature loss.
View cold-storage door
Heated-frame door rated for sub-zero rooms, keeping the seal free of frost.
View freezer door
Smooth, wipe-down door for pharma and electronics clean rooms where pressure separation matters.
View clean-room door
Heavier curtain and wind-lock build for high-cycle bays and external openings.
View industrial / exterior doorSpecify the right one
Three closures do different jobs. Here is where each fits, so you specify the right one rather than the nearest one.
| High-speed door | Rolling shutter | Sectional door | |
|---|---|---|---|
| Opens in | Seconds | Slower, geared | Moderate |
| Built for | Speed and sealing on a busy opening | A secure closure | An insulated overhead closure |
| Cycle rate | Very high, many times a shift | Low to moderate | Moderate |
| Seal & temperature | Tight, fast reseal | Basic | Insulated panel |
| Best placed | Internal traffic, cold and clean rooms | Shopfronts, secure bays | Loading bays, external walls |
Why the shortlist ends here
A plant purchase manager checks four things: do they supply plants like mine, are they close enough to service me, can they build what I need, and will someone answer the phone. Here is how Yadav answers all four.
Get a quoteSelf-repairing curtains re-seat after a knock, so a trolley strike does not stop the line.
Plants on the Neemrana-Bawal belt audited and buy from us; the same team covers Faridabad.
Every door is sized to the surveyed opening and duty, not pulled off a shelf.
Manufactured under an ISO 9001 quality system with CE-marked product.
AMC and spares from our NCR team based at the Gurugram office.
Where these go to work
Machining, paint and stores separation in NIT and Sector 24 plants.
Assembly halls and fabrication bays on the Mathura Road belt.
High-cycle dispatch openings towards Ballabgarh.
Hygienic doors between wet and dry zones.
Chillers and dispatch docks that must hold temperature.
Peer proof, not promises
Japanese and European plants audit a supplier before they place an order. These are plants in your corridor that cleared us and buy their entrance automation from Neemrana.
Recent handovers
Ghiloth
30 motorised rolling shutters, supply to handover in 20 days
Bawal
Automatic mesh-type rolling shutters
Neemrana
Powder-coated shutters with rubber bottom seal
Bawal
Four-panel motorised sliding door
Answers for buyers and specifiers
The real questions people search on Google and ask an AI assistant, answered straight. No pricing games, no jargon.
A smooth, wipe-down clean-room door that supports pressure separation between graded areas. It cleans easily and cycles fast enough to keep the differential.
Yes, with a heavier curtain and a wind-lock build. External and high-cycle bays use a reinforced door rather than a light internal curtain.
On a self-repairing door the curtain pops out of the guides and re-seats on the next cycle, so a knock does not stop the line. On other types we hold spares locally for a quick repair.
A PVC high-speed door separates a paint or finishing area from machining dust, and a self-repairing door suits openings where forklifts or trolleys sometimes touch the curtain. The choice follows the traffic and what has to stay on each side.
Often, on an internal opening that is used many times a shift. We check the opening, headroom and side-room on survey. If the opening also needs night security, the usual answer is a high-speed door inside and a rolling shutter outside.
Safety photocells or a light curtain across the opening and a safety edge on the bottom of the curtain, which stop or reverse it on contact. The safety schedule is listed on the drawing you approve.
Yes. Interlocks are common on clean rooms and airlocks, so one door cannot open until the other is closed. The interlock logic is set in the control panel and shown on the drawing.
Yes, and earlier is better. If we see the drawings before the walls go up, the opening size, headroom and power point are set for the door rather than adapted to it later.
Yadav Entrance Automation Pvt. Ltd. manufactures high-speed doors at its works at Neemrana, Rajasthan and installs them across Faridabad with its own engineers. We have been building entrance automation equipment since 2011, with 500+ installations across 50+ cities.
No. We hold no premises inside Faridabad, and we would rather say so. Faridabad is served from our Sales & Corporate Office at Sector 83, Gurugram, with manufacturing at Neemrana, Rajasthan. Survey, installation and service in Faridabad are done by the same NCR team that covers Gurugram.
All of Faridabad, including NIT Faridabad, Sectors 24, 25, 58 and 59, Ballabgarh and the Mathura Road belt. Tell us the site address with your enquiry and we will confirm the survey date before quoting rather than after.
Internal openings between machining, paint and stores in auto-component and engineering plants across NIT Faridabad and Sectors 24, 25, 58 and 59, and dispatch openings in warehouses towards Ballabgarh.
We do not publish a standard figure because it depends on the current survey schedule. Ask when you enquire and you get an actual date, in writing.
Yes. We supply genuine spares and offer Annual Maintenance Contracts for equipment we manufacture, handled by the NCR service team that covers Faridabad. On high-cycle openings the service interval should follow the cycle count, not the calendar.
Yes. The works are at Neemrana on the Delhi-Jaipur NH-48 corridor. Buyers from Faridabad usually combine a plant visit with a meeting at the Gurugram office. Call +91 95492 20707 ahead so someone is free to show you the shop floor.
Yadav Entrance Automation is a high speed door manufacturer for Faridabad, building PVC, self-repairing (zipper), insulated, cold-storage and clean-room high-speed doors, also called rapid or fast-action doors. Built at Neemrana and installed across NIT Faridabad, Ballabgarh and the Mathura Road belt by our NCR team from Gurugram.
Send the opening or dock size, the application and a rough timeline. Our team will review the requirements and contact you about a project-specific quote.
A high-speed door is a fabric or PVC door that opens and closes in seconds. We manufacture high-speed doors at Neemrana on the Delhi-Jaipur NH-48 corridor and install them across Faridabad with our own engineers — the same team that surveys the opening also commissions the equipment.
For a side-by-side comparison before you enquire, read our buyer's guide: High-speed door or rolling shutter? How to choose for your opening.
Reference: applicable products are CE marked (European Commission); Indian Standards are published by the Bureau of Indian Standards.
Yadav Entrance Automation Pvt. Ltd. manufactures high-speed doors at our plant at Neemrana, Rajasthan on the Delhi-Jaipur NH-48 corridor, within easy reach of Gurugram (Gurgaon), and installs across Delhi NCR with our own engineers. We have been building entrance automation equipment since 2011.
Yes. Our NCR and Haryana coverage includes Gurugram (Gurgaon), Manesar, Bhiwadi, Neemrana, Bawal, Faridabad, Noida, Jhajjar, Bahadurgarh and Delhi. A sales and service team is based in Delhi NCR, and the plant sits on the corridor, so survey and installation scheduling is quicker here than for most of our coverage area.
Sites in Gurugram, Manesar, Bhiwadi, Bawal and along the Delhi-Jaipur corridor are quickest, because both the plant and a service team are close. Ask when you enquire and we will give you an actual date rather than a general lead time.
Yes. We supply genuine spares and offer Annual Maintenance Contracts for equipment we manufacture, with a service team covering the NCR and Haryana corridor. On high-cycle equipment, maintenance should follow the cycle count rather than the calendar.
Yes. The plant is at Neemrana on the Delhi-Jaipur NH-48 corridor, a straightforward drive from Gurugram. Call +91 95492 20707 ahead so a visit can be scheduled and someone is free to show you the shop floor.