Rolling Shutters: Motorized, Aluminium & Galvanized

Yadav Entrance Automation Pvt. Ltd. manufactures rolling shutters in India, at our plant at Neemrana, Rajasthan on the Delhi-Jaipur NH-48 corridor. We have been building entrance automation equipment since 2011, with more than 500 installations across over 50 cities. Equipment is made to the measured opening rather than to a catalogue size, then installed and commissioned by our own engineers.

A rolling shutter is a steel or aluminium curtain that coils above the opening on a barrel. It is specified against the opening it serves and the way that opening is used, so two openings of the same width can need different equipment. We build rolling shutters for factory entrances, godowns, service yards, shopfronts and warehouse openings.

We quote per project rather than publishing a price, because the figure moves with the opening size, the slat material and finish, whether it is manual or motorised, and the duty cycle. Send the opening dimensions, the site location and how the opening is used, and an engineer will come back with a drawing and a written quotation. That is faster than a list price that would need revising once the site is measured.

We install and service across North and West India, with the plant at Neemrana and teams in Delhi NCR and Gujarat. Installations to date cover more than 50 cities, concentrated in the Delhi-Jaipur corridor, Haryana, Rajasthan and Gujarat. Tell us the site location with your enquiry and we will confirm coverage before quoting.

Yes, where the product supports it. Motorised operation is specified against the weight being moved and the number of cycles per day, not simply added on. The drive, the control panel and the safety devices are listed on the technical drawing you approve before manufacture, so nothing about the automation is a surprise on site.

Standard Indian industrial mains: 230V single-phase or 415V three-phase at 50 Hz. Which one applies depends on the product, the size of the opening and the duty cycle. The requirement is confirmed on the approved drawing so your electrical contractor can position the supply and isolator before delivery.

Clear opening width and height first. The daylight opening, not the wall opening. Then the headroom above the opening and the free side-room each side. Add the power available at the position, how many openings, and roughly how often each is used in a shift. Those figures let an engineer rule out the wrong products before visiting.

We manufacture, install and commission with our own team, and we do not sub-contract installation of our own equipment. How well a unit is fitted to its opening decides how long it lasts, so it is not work we hand off. Handover includes operating instructions on site.

Yes. We supply genuine spares and offer Annual Maintenance Contracts for the equipment we manufacture. On high-cycle equipment maintenance matters more than most buyers expect, because wear tracks cycles rather than calendar age. Tell us the site and the equipment and we will route it to the nearest service team.

Our manufacturing is certified to ISO 9001 and applicable products are CE marked. Structural steelwork commonly references IS 2062 and rolling shutters IS 6248, both published by the Bureau of Indian Standards; fire-resistance testing is commonly referenced to EN 1634. If your specification names a standard, send the clause with the enquiry so it is written into the drawing.

Yes, and most industrial openings are non-standard. Equipment is built to the measured opening rather than to a catalogue size. We take the clear width, clear height, headroom and side-room on site, then confirm the achievable size on the drawing before manufacture begins.

It depends on the product and whether the opening is standard or bespoke, and it moves with material availability and the current order book. Rather than quote a general figure that may not hold, we confirm a delivery date in writing with the quotation.

Yes. We supply end users directly and also work as a vendor to main contractors, PMCs and design consultants. We are GST registered and manufacture under Make in India, which matters for government and PSU procurement. For tendered work we can provide drawings, product data and the compliance documentation the specification calls for.

For powered equipment, typically safety photocells across the opening, a safety edge where applicable, limit switches at both travel ends, and a manual release for use during a power cut. Vehicle equipment can add loop detectors. The exact schedule is listed on the drawing you approve, so check that rather than assuming a standard set.

Use the enquiry form on this page and the details reach our team directly, or call and send a WhatsApp message on +91 95492 20707, or email [email protected]. If you already hold drawings or a specification, say so and an engineer will respond rather than a generic reply.

It reduces the conditions that cause it by keeping the warm-side surface closer to ambient, but condensation depends on humidity and airflow as well as temperature. Tell us the conditions at your opening and we will advise honestly on whether the shutter alone will resolve it.

The curtain is heavier than a single-skin one, so it is motorised and the motor is sized for the extra weight. Where cycle time genuinely matters, a high-speed door is the better answer for the traffic and the insulated shutter is the better answer for the overnight seal.

No, and both matter. The thermal break is the PUF core resisting heat conduction through the curtain. Seals are the brushes and gaskets closing the gaps at the guides and floor. An insulated curtain with poor perimeter sealing still loses energy.

Pre-galvanized steel is coated as a coil before the lath is formed; hot-dip is coated after fabrication, giving a heavier layer that also covers cut edges. Hot-dip generally suits harsher exposure. Tell us your environment and we will recommend rather than default.

Yes, but the surface must be prepared for it, because paint does not adhere to bare zinc as readily as it does to steel. We handle that in our own powder coat facility, so tell us the RAL colour you need at enquiry rather than painting on site later.

Both resist salt air well. Galvanized steel is stronger and better where impact is likely; aluminium cannot corrode at all but is softer. If forklifts pass through the opening, that usually settles it in favour of galvanized steel.