Rolling Shutter Manufacturer in Ahmedabad

Yadav Entrance Automation Pvt. Ltd. manufactures rolling shutters at its works at Neemrana, Rajasthan and serves Ahmedabad through its Gujarat branch office at Vithalpur Chokdi, Vithalpur. Survey, installation and service in Gujarat are handled by that team. We have been manufacturing entrance automation equipment since 2011.

A rolling shutter is a steel or aluminium curtain that coils above the opening on a barrel. Because it coils rather than swings or slides, it needs very little side-room and clears the opening completely when raised, which is why it suits factory entrances and godowns where space around the opening is tight.

We quote per project rather than publishing a price, because the figure moves with the opening size, the slat material and finish, whether it is manual or motorised, and the duty cycle. Send the opening dimensions and the site location and an engineer returns a drawing and a written quotation.

Yes. Our Gujarat branch covers Ahmedabad, Sanand, Vithalpur and Mandal, and the wider industrial belt on a project basis. Tell us the site location with your enquiry and we will confirm coverage before quoting rather than after.

Yes. Motorised shutters use a tubular or side-mounted motor sized against the curtain weight and the number of cycles per day, with a manual release for power cuts. The motor, control panel and safety devices are listed on the technical drawing you approve before manufacture.

Standard Indian industrial mains: 230V single-phase or 415V three-phase at 50 Hz. Which applies depends on the curtain weight, the opening size and the duty cycle. It is confirmed on the approved drawing so your electrical contractor can position the supply and isolator before delivery.

Hot-dip galvanised slats generally outlast a painted finish in humid, coastal and chemical environments, and finish choice is the commonest reason a shutter fails earlier than it should. Tell us the site environment and we will specify the finish against it rather than defaulting.

Clear opening width and height — the daylight opening, not the wall opening — plus the lintel or headroom above it and the free side-room each side. Add the power available at the opening and roughly how many times it is used in a shift.

Yes, and most industrial openings are non-standard. Shutters are built to the measured opening rather than to a catalogue size. We confirm the achievable size on the drawing before anything is cut, because the guides and barrel take up space the wall opening does not show.

Enough for the curtain to coil above the opening, plus the barrel and the motor. The exact figure depends on the slat profile, the door height and whether the drive is central or side-mounted, so it is confirmed on the drawing rather than estimated. Where headroom is tight, a sectional door may fit better.

Yes. Foam-filled slats are used where the opening separates temperature zones or where noise needs cutting. For hard temperature separation with high traffic, a high-speed door often performs better, and we will say so rather than sell the wrong product.

Yes. A fire-rated shutter is a tested assembly with automatic descent, used where a wide industrial opening sits in a fire compartment line and a swing leaf will not fit. If your specification names a rating, send the clause so it is written into the drawing.

Typically safety photocells across the opening, a bottom safety edge, limit switches at both travel ends and a manual release for power cuts. The exact schedule is listed on the drawing you approve, so check that rather than assuming a standard set.

We manufacture, install and commission with our own team. We do not sub-contract installation of our own equipment, because how squarely a shutter is fitted to its opening decides how long the guides, curtain and motor last.

It depends on the product and whether the opening is standard or bespoke, and it moves with material availability and the current order book. We confirm a delivery date in writing with the quotation rather than quoting a general figure that may not hold.

Yes, through the Gujarat branch team. We supply genuine spares and offer Annual Maintenance Contracts for equipment we manufacture. On high-cycle shutters, the service interval should follow the cycle count rather than the calendar.

Manufacturing is ISO 9001 certified and products are CE marked where applicable. IS 6248, published by the Bureau of Indian Standards, is the standard commonly referenced for metal rolling shutters. Steel sections used in fabrication reference IS 2062.

Yes. We supply end users directly and act as a vendor to main contractors, PMCs and design consultants. We are GST registered and manufacture under Make in India, which matters for government and PSU procurement, and can provide the documentation a tender calls for.

Often yes, and it is worth asking, because reusing sound steelwork saves cost and downtime. It depends on whether the existing guides and lintel are square, plumb and sound enough to carry a new curtain. That is a site-survey question rather than a catalogue one.

Wear tracks cycles rather than age. The parts to watch are the bottom rail and seals, guide rails collecting debris, spring or counterbalance tension drifting, and photocell alignment being knocked by traffic. Test the manual release while nothing is wrong.

Yes. The works are at Neemrana, Rajasthan on the Delhi-Jaipur NH-48 corridor. Call +91 95492 20707 ahead so a visit can be scheduled. Seeing equipment built and tested is the fastest way to judge a manufacturer against a spec sheet.

Use the enquiry form on this page and it reaches our team directly, or call and WhatsApp +91 95492 20707, or email [email protected]. Mention that the site is in Gujarat and the branch team picks it up.